In the unstable patellofemoral joint (PFJ), the patella will articulate in an abnormal manner, producing an uneven distribution of forces. It is hypothesised that incongruency of the PFJ, even without clinical instability, may lead to degenerative changes. The aim of this study was to record the change in joint contact area of the PFJ after stabilisation surgery using an established and validated MRI mapping technique.

A prospective MRI imaging study of patients with a history of PFJ instability was performed. The patellofemoral joints were imaged with the use of an MRI scan during active movement from 0° through to 40° of flexion. The congruency through measurement of the contact surface area was mapped in 5-mm intervals on axial slices. Post-stabilisation surgery contact area was compared to the pre-surgery contact area.

In all, 26 patients were studied. The cohort included 12 male and 14 female patients with a mean age of 26 (15-43). The greatest mean differences in congruency between pre- and post-stabilised PFJs were observed at 0-10 degrees of flexion (0.54 cm² versus 1.18 cm², p = 0.04) and between 11° and 20° flexion (1.80 cm² versus 3.45 cm²; p = 0.01).

PFJ stabilisation procedures increase joint congruency. If a single axial series is to be obtained on MRI scan to compare the pre- and post-surgery joint congruity, the authors recommend 11° to 20° of tibiofemoral flexion as this was shown to have the greatest difference in contact surface area between pre- and post-operative congruency.

Nearly a quarter of screws cause damage during insertion by stripping the bone, reducing pullout strength by over 80%. Studies assessing surgically achieved tightness have predominately shown that variations between individual surgeons can lead to underpowered investigations. Further to the variables that have been previously explored, several basic aspects related to tightening screws have not been evaluated with regards to how they affect screw insertion. This study aims to identify the achieved tightness for several variables, firstly to better understand factors related to achieving optimal intraoperative screw purchase and secondly to establish improved methodologies for future studies.

Two torque screwdrivers were used consecutively by two orthopaedic surgeons to insert 60 cortical, non-locking, stainless-steel screws of 3.5 mm diameter through a 3.5 mm plate, into custom-made 4 mm thick 20 PCF sheets of Sawbone, mounted on a custom-made jig. Screws were inserted to optimal tightness subjectively chosen by each surgeon. The jig was attached to a bench for vertical screw insertion, before a further 60 screws were inserted using the first torque screwdriver with the jig mounted vertically, enabling horizontal screw insertion. Following the decision to use the first screwdriver to insert the remaining screws in the vertical position for the other variables, the following test parameters were assessed with 60 screws inserted per surgeon: without gloves, double surgical gloves, single surgical gloves, non-sterile nitrile gloves and, with and then without augmented feedback (using digitally displayed real-time achieved torque). For all tests, except when augmented feedback was used, the surgeon was blinded to the insertion torque. Once the stopping torque was reached, screws were tightened until the stripping torque was found, this being used to calculate tightness (stopping/stripping torque ratio). Screws were recorded to have stripped the material if the stopping torque was greater than the stripping torque. Following tests of normality, Mann-Whitney-U comparisons were performed between and combining both surgeons for each variable, with Bonferroni corrections for multiple comparisons.

There was no significant (p=0.29) difference in the achieved tightness between different torque screw drivers nor different jig positions (p=0.53). The use of any gloves led to significant (p < 0 .001) increases in achieved tightness compared to not using gloves for one surgeon but made no difference for the other (p=0.38–0.74). Using augmented feedback was found to virtually eliminate stripping. For one surgeon average tightness increased significantly (p < 0 .001) when torque values were displayed from 55 to 75%, whilst for the other, this was associated with significantly decreases (p < 0 .001), 72 to 57%, both surgeons returned to their pre-augmentation tightness when it was removed.

Individual techniques make a considerable difference to the impact from some variables involved when inserting screws. However, the orientation of screws insertion and the type of screwdriver did not affect achieved screw tightness. Using visual feedback reduces rates of stripping and investigating ways to incorporate this into clinical use are recommended. Further work is underway into the effect of other variables such as bone density and cortical thickness.

Cement-induced thermal osteonecrosis is well documented, as is the potential for nerve injury from thermal energy. Cement is often used to augment fixation following excision of humeral metastases. Porcine femurs were used as a model. We sought to find out the maximum temperatures that would be reached in various parts of the bone during the cement setting process, to explore what negative effects this might have on neighbouring bone and nerve.

A 12mm by 12mm window was cut from 12 porcine femoral shafts, and Palacos R+D cement injected into the defect. As cement set, bone surface temperature was measured using infra-red thermal imaging and thermocouples used to measure temperatures at the bone-cement interface, 5mm from the cement bolus, 10mm from cement bolus and an area running around the shaft replicating radial nerve.

Bone surface temperature rose to a maximum of 34.0 C (on average), and 32.9 C in the ‘radial nerve’ thermocouple. Notably, in two bones there were fractures during specimen preparation, and maximum temperatures in these two areas exceeded 41 degrees C.

Average maximum temperatures were 58.1 C, 36.5 C and 30.1 C at the bone cement interface, 5mm and 10mm from the cement bolus respectively.

Triple-tapered cemented stems were developed in the hope that they would reduce aseptic loosening and prevent calcar bone loss.

Between March 2005 and April 2008, a consecutive series of 415 primary C-stem AMT hip arthroplasties in 386 patients were performed under the care of three surgeons at our institution. When all the patients had reached the 5-year anniversary of surgery, functional questionnaires were sent out by mail. In the event of non-response, reminders were sent by post before the patients were contacted by telephone. Postoperative radiographs were also reviewed.

Follow-up ranges from 60 to 99 months, with a mean of 76 months. 32 hips (8%) were lost to follow-up. The median OHS was 40, median SF-12 mental component score (MCS) was 50, and median SF-12 physical component score (PCS) was 39. Radiographic review showed that aseptic femoral component loosening has yet to be observed. At 99 months follow up, stem survivorship is 96.9% (95% confidence interval (CI) 82.5 to 99.5). Adverse events such as calcar fracture, greater trochanter fracture and dislocation were rare at <1%.

The C-stem AMT demonstrates excellent implant survivorship at 5–8 year follow-up, as well as good midterm functional outcome.