The aim of this study was to compare the strain pattern in intact and resurfaced femurs using validated third generation composite femurs and rosette strain gauges.
Further tests were carried out in which an abductor load was included in the model. Testing was done at 600N and repeated thrice for each femur. The principal strains were calculated and compared with the the principal strains without the abductor load.
Controversy exists as to whether the biomechanical properties of a 360 lumbar fusion are influenced by the order in which the anterior and posterior components of the procedure are performed. The fusion technique used Magerl screws to effect the posterior fusion and a Syncage implant (Stratec) to effect the anterior component of the fusion. Isolated motion segments from calf spines were tested in each of two groups of five. In the first group the posterior fusion was performed first and in the second group the anterior fusion was performed first. Loads were applied as a dead weight of 2Nm in each range of movement of the spine (flexion/extension, lateral flexion and rotation). The range of movement was measured using the Qualisys motion analysis software linked to a set of five cameras, using external marker clusters attached to the vertebral bodies. Each motion segment was tested prior to instrumentation, post anterior or posterior instrumentation and with both anterior and posterior instrumentation. Ranges of movement following 360 instrumentation were increased in all planes tested when posterior fixation was performed first; flexion/extension 26% v 55% (p=0.020), lateral flexion 18% v 34% (p=0.382), and rotation 18% v 73% (p=0.034). It was concluded that posterior fixation should not be performed prior to anterior fixation as this results in a significant loss of stability in both flexion/extension and rotation
Interbody fusion is increasingly widely used as a treatment for intervertebral disc disorders, but the biomechanics of the procedure are not well understood. The compressive loads through the spine are largely carried by the implant or bone graft, which typically rests on a relatively small area of the vertebral body. As the compressive strength of the bone is very low, subsidence of the implants into the vertebral bodies is a common clinical complication. Previous biomechanical studies of spinal fusion have concentrated on the stiffness of the constructs, which is important in promoting fusion. Preliminary studies have shown that there are large differences in compressive strength between different implant systems, and gave an insight into the biomechanical factors that are important in determining the strength of spinal fusion constructs. This paper reports part of a larger on going study comparing anterior and posterior fusion systems, with various methods of fixation. A major problem in interpreting the results of these tests is to distinguish between initial settling of the implants and the onset of failure to construct. We have developed a novel technique using acoustic emission monitoring to detect microcracking in the bones, which allows the onset of failure to be distinguished from initial bedding in of the implants. Two implant systems were tested, the Syncage and the Contact fusion cage. The cages were implanted into porcine lumbar spines at L4-L5, and the implanted motion segment was then dissected out. Steel plates were mounted on each end using bone cement to ensure an even distribution of load through the vertebral body. The complete constructs were then loaded in compression, using acoustic emission sensors to detect microcracking in the bones. The load was cyclically increased in o.5kN steps until failure occurred. The acoustic emission technique gave a sensitive indication of the onset of damage in the bones and allowed the initial settling of the implant under load to be identified. Using cyclic unloading and reloading, it was possible to accurately identify whether this damage had weakened the construct or increased its strength by redistributing stress concentrations. Initial results indicate that the Contact fusion cage fails at a much lower load than the Syncage in this model; this is ascribed to the very small contact areas between the cage and the vertebral body, which results in high compressive stresses in the bone. Under large compressive loads it appears that the constructs become unstable, and fail by buckling and plastic collapse of the vertebral bodies. Various failure models are therefore possible depending on which part of the vertebral body starts to collapse first.
We measured the proximal migration of 265 acetabular cups over seven years and correlated the findings with clinical outcome and acetabular revision for aseptic loosening. Cups which eventually became aseptically loose were shown to migrate more rapidly than successful cups. The average proximal migration at two years postoperatively for four groups of cups showed a monotonic relationship to the acetabular revision rate for aseptic loosening at 6.5 years. We conclude that acetabular cups which develop aseptic loosening as evidenced by pain, revision or screw fracture show increased proximal migration by one year, and that the 'migration rate' at two years can be used to predict the acetabular revision rate from aseptic loosening at 6.5 years.
Individual components of a total hip replacement are difficult to evaluate and quantify. We have studied the assessment of the acetabular component, and conclude that the measurement of migration allows the comparison of implants, although there is no established link between migration and significant loosening. A method of measurement based on clinical radiographs has been developed, and its limitations estimated. The accuracy of the technique was calculated to be +/- 3 mm.
