P59 THERMOGRAPHIC INVESTIGATION OF DRILLING OF BONE

CY Ng; F Borocin; A Muir; H Simpson

doi:10.1302/0301-620X.90BSUPP_II.0900383a

Article alerts Social media

Current issue

P59 THERMOGRAPHIC INVESTIGATION OF DRILLING OF BONE

CY Ng
F Borocin
A Muir
H Simpson

P59 THERMOGRAPHIC INVESTIGATION OF DRILLING OF BONE

Ng C, Borocin F, Muir A, Simpson H. P59 THERMOGRAPHIC INVESTIGATION OF DRILLING OF BONE. Orthop Procs. 2008;90-B(SUPP_II):383-383. doi:10.1302/0301-620X.90BSUPP_II.0900383a

Ng, CY, et al. “P59 THERMOGRAPHIC INVESTIGATION OF DRILLING OF BONE.” Orthopaedic Proceedings, vol. 90-B, no. SUPP_II, 2008, pp. 383-383., https://doi.org/10.1302/0301-620X.90BSUPP_II.0900383a

Ng, C., Borocin, F., Muir, A., & Simpson, H. (2008). P59 THERMOGRAPHIC INVESTIGATION OF DRILLING OF BONE. Orthopaedic Proceedings, 90-B(SUPP_II), 383-383. https://doi.org/10.1302/0301-620X.90BSUPP_II.0900383a

Ng, C., Borocin, F., Muir, A. and Simpson, H. (2008) “P59 THERMOGRAPHIC INVESTIGATION OF DRILLING OF BONE.” Orthopaedic Proceedings, 90-B(SUPP_II), pp. 383-383. Available at: https://doi.org/10.1302/0301-620X.90BSUPP_II.0900383a

Ng, CY, F Borocin, A Muir, and H Simpson. “P59 THERMOGRAPHIC INVESTIGATION OF DRILLING OF BONE.” Orthopaedic Proceedings 90-B, no. SUPP_II (2008): 383-383. https://doi.org/10.1302/0301-620X.90BSUPP_II.0900383a

Ng C, Borocin F, Muir A, Simpson H. P59 THERMOGRAPHIC INVESTIGATION OF DRILLING OF BONE. Orthop Procs. 2008 Jul 1;90-B(SUPP_II):383-383. https://doi.org/10.1302/0301-620X.90BSUPP_II.0900383a

Copy to clipboard

BibTeX

EndNote

RIS

Abstract

Thermonecrosis either results in bone loss which may weaken the purchase of surgically-inserted screws leading to loosening or the dead bone may remain in situ and become infected resulting in a ring sequestrum. The aim of this project was to measure the heat generated during drilling of bone. By using a novel realtime thermal camera the thermal events could be visualised topographically.

An experimental setup comprising a force table, an infrared camera, a power drill and a new surgical 2.5mm drill bit was constructed. This enabled measurements of the force applied and temperature changes in sheep cortical bone during a drilling operation. The temperature was observed throughout the drilling period and for further 15s after the drill bit was withdrawn. Images were grabbed using a LAND FTI Mv thermal camera which was driven by LIPS Mini software. Calibration was made in the range 20-200 degrees C, the upper value being provided by a high wattage resistor. Data was processed using routines written in MATLAB.

It was found that 12s were required to drill through a single cortex. Within one second of drilling, the maximum recorded temperature in the vicinity of the drill increased from the baseline of 20 to 170 degrees C. It remained above this temperature for 25s. Immediately after the drill bit was withdrawn, a region of approximately 15mm of diameter of cortical surface had a sustained temperature above 50 degrees C. After 15s of cooling, this diameter had only reduced to 10mm. By modelling the cooling curve, the maximum temperature at the drill tip was extrapolated to be between 500-600 degrees C.

Thermography has proven to be useful in the study of the thermal characteristics of bone during drilling. The process of drilling generates significant increase in temperature in the vicinity of the drill. This temperature elevation has been found to be sustained for a significant period of time.

Correspondence should be addressed to Mr Carlos Wigderowitz, Senior Lecturer, University Department of Orthopaedic and Trauma Surgery, Ninewells Hospital and Medical School, Dundee DD1 9SY.